A Beginner's Guide to DJI Mini 2 SE & DJI Mini 4K

Introducing DJI Mini 2 SE and DJI Mini 4K – lightweight and compact drones weighing under 249 g. Experience up to 31 minutes of flight time, exceptional wind resistance at level 5, and the convenience of one-tap takeoff, smart RTH, QuickShots, and Panorama modes. These user-friendly drones are designed to make your aerial adventures a breeze.

Flight performance, image transmission, and intelligent features of DJI Mini 2 SE and DJI Mini 4K have all improved significantly, compared with DJI Mini SE. Comparisons are as follows:

DJI Mini 2 VS DJI Mini 2 SE:

When the new drone is on hand, activate it before use. Download DJI Fly, connect your drone, remote controller and mobile device, and activate your product following the prompts.

Consult the content below for a guide to powering on and activating your device.

Push the lower buckle of the gimbal protector towards the camera to remove the gimbal protector.

· Attaching the Gimbal Protector

1. Snap the buckle at the upper part of the gimbal protector into the slot on the aircraft.
2. In the same way, snap the lower buckle into the slot at the bottom of the aircraft.

Press and hold the Power button on the aircraft or remote controller to power on or off the device.

• Aircraft

• Remote Controller

As we all know, there are two types of propeller/motor: CW and CCW, and you can easily recognize it through the mark on it. Before mounting the propeller,
better confirm the mark on each first.

DJI Mini 2 SE and DJI Mini 4K has been installed with propellers before leaving the factory. In case of a propeller replacement, please refer to the steps below.

· Distinguishing between Propellers

If the propeller is mounted in an improper way, the drone cannot take off.

① Propeller CW

② Propeller CCW

· Attaching or Replacing the Propellers

Step 1: Place the drone horizontally and make sure that the drone's camera faces forwards;

Step 2: Tighten the propellers with a mark onto the motors using the provided screwdriver.

Step 3: Tighten the propellers without a mark onto the remaining motors.

To learn more about how to replace the propellers, watch the video:

（This video applies to DJI Mini 2 SE and DJI Mini 4K）

If you would like to install or remove the battery from the drone, please see below:

· Installing the Battery

· Removing the Battery

DJI Mini 2 SE and DJI Mini 4K requires activation before first use. Follow the on-screen prompts to activate the device using DJI Fly.

DJI Fly is required for product activation and connection.

Before takeoff, connect the drone to the remote controller and mobile device.

Watch this video for the detailed linking steps:

（This video applies to DJI Mini 2 SE and DJI Mini 4K） 

Make sure that the aircraft, remote controller, and mobile device are connected and linking is successfully. Launch the DJI Fly app, and then complete the activation following the on-screen instructions (an Internet connection is required for activation).   

For an overview of how to activate your device, watch the video below:

（This video applies to DJI Mini 2 SE and DJI Mini 4K）

The DJI Mini 2 SE and DJI Mini 4K firmware needs to be updated with DJI Fly. Power on the aircraft and remote controller, and make sure that the remote controller is linked to the aircraft. Follow the on-screen instructions to update the firmware and note that Internet is required.

Click Updating Your Drone Firmware to know more.

（This video applies to DJI Mini 2 SE and DJI Mini 4K）

Press the Power button on the aircraft and remote controller for one second respectively, and the status LEDs will light up. When only one LED is on, please charge the device before the flight.

As DJI Mini 2 SE and DJI Mini 4K does not come with a charger, you can refer to the following content to select an appropriate charger.

· DJI Mini 2 SE and DJI Mini 4K supports QC and USB PD fast-charging protocols, and supports up to 29 W of input power.

· If you would like to purchase a charger, we recommend you add DJI 18W USB-C Charger to your cart.

· Other common PD fast charging chargers are supported, such as Apple USB‑C power adapters and Android GaN chargers.

· If a PD fast charger is currently not available, you can also use a charger with a Type-C port for charging, but the charging speed may be relatively slower.

· Connecting the aircraft with the battery mounted for charging

· Using the Battery Charging Hub

· Charging the DJI RC-N1 Remote Controller

· Charging the aircraft

The battery can be fully charged in about 1 hour and 22 minutes by a charger with a maximum charging power of 18 W.

1. If a battery will not be used for 10 days or longer, discharge it to 40%-65% state of charge (until LED 3 lights up or blinks) for storage.

2. Charge and discharge the battery about every three months to maintain good conditions of the battery and extend lifetime of the battery. If the battery is stored after completely drained, it may over-discharge and be damaged.

3. Always store Intelligent Flight Batteries in a well-ventilated place.

4. The battery will enter Hibernation mode if depleted and stored for a long period of time. Recharge the battery to bring it out of Hibernation mode.

Follow the steps below to prepare to use the aircraft and remote controller.

Step 1: Remove the gimbal protector and unfold the aircraft arms.

Step 2: Check the battery level of the drone battery, power on the drone, and place it on a flat ground. Note that the rear of the drone should face towards you.

（This video applies to DJI Mini 2 SE and DJI Mini 4K） 

If the gimbal is skewed or DJI Fly App prompts for gimbal calibration, you can refer to the following pictures.Path: ···＞ Control ＞ Gimbal Calibration ＞ Auto/Manual

Step 1: Remove the control sticks from the storage slots at the bottom of the remote controller and screw them into place.

Step 2: Place your mobile device in the holder, and connect the mobile device with the RC cable.

Step 3: Check the battery level of the remote controller and power on the remote controller. Then launch DJI Fly.

（This video applies to DJI Mini 2 SE and DJI Mini 4K）

Watch this video to guide you through your first flight with DJI Mini 2 SE and DJI Mini 4K:

（This video applies to DJI Mini 2 SE and DJI Mini 4K）

DJI Mini 2 SE and DJI Mini 4K supports shooting in Dronie, Rocket, Circle, Helix, and Boomerang modes. The drone records according to the selected shooting mode and automatically generates a short video without pushing control sticks.

For an overview of how to use QuickShots, watch the video below:

（This video applies to DJI Mini 2 SE and DJI Mini 4K）

After selecting from Wide-Angle, 180°, and Sphere panoramas, DJI Mini 2 SE and DJI Mini 4K will automatically capture pictures and stitch them to a panoramic masterpiece almost instantly.

DJI Mini 2 SE and DJI Mini 4K supports up to 4x digital zoom to create the perfect composition.

When using DJI RC-N1 remote controller with your mobile device, you can live stream with your Mini 2 SE via DJI Fly. Enter the camera view and go to 「"..." > Transmission > Enable Livestreaming」to broadcast the camera view in real time. DJI Mini 2 SE and DJI Mini 4K supports livestream platforms and multiple resolutions for you to choose from and connect with your world face-to-face at any time.

Note to input the RTMP address as below: RTMP address/stream key. Please do add the "/" (forward slash) between the RTMP address and the stream key. Only in this way, can the live streaming screen be displayed.

Smart RTH is initiated either by tapping the RTH icon at the left side of the screen in the app or by pressing and holding the RTH button on the remote controller.

Watch the tutorial below learn how to use Smart RTH:

DJI Mini 2 SE and DJI Mini 4K does not include an internal storage, so you cannot snap some photos and record videos or use QuickShots if you forget to bring a memory card. It is recommended to install a microSD card before shooting.

The DJI Mini 2 SE and DJI Mini 4K package does not come with a microSD card. DJI Mini 2 SE and DJI Mini 4K supports microSD cards with capabilities of up to 256GB, and we recommend you choose a microSD card that is strictly tested: 

16G：

Sandisk Extreme

32G：

Samsung Pro Endurance

Samsung Evo Plus, SanDisk Industrial

SanDisk Extreme V30 A2

SanDisk Extreme Pro V30 A1

SanDisk Extreme Pro V30 A2

Lexar 633x

Lexar 667x

64G：

Samsung Pro Endurance

Samsung Evo Plus

SanDisk Extreme V30 A1

SanDisk Extreme V30 A2

Lexar 633x

Lexar 667x

Lexar 1000x

Lexar High Endurance

Toshiba EXCERIA M303 V30 A1

128G：

Samsung Pro Plus

Samsung Evo Plus

SanDisk Extreme V30 A2

SanDisk Extreme Plus V30 A1

SanDisk Extreme Plus V30 A2

Lexar 633x

Lexar 667x

Lexar 1000x

Lexar High Endurance

Toshiba EXCERIA M303 V30 A1

256G：

SanDisk Extreme V30 A2

If you have purchased a memory card, you can insert it into the black memory card adapter, which can be attached to the TF slot on PC for further file transfer. Please note that the memory card is inserted into the drone without the card adapter.

Please see below for how to install and remove a memory card from the drone:

· Installing a Memory Card

The raw footage captured by DJI Mini 2 SE and DJI Mini 4K is stored in the microSD card. You can connect the drone to the remote controller and mobile device, and download the photos or videos through the app.

Please fly your drone in a safe environment, and strictly abide by local laws and regulations. Before a takeoff, have a glance at the nearby restricted and GEO zones.

1. For safety reasons, you should never fly above people, animals, or moving vehicles.

2. Minimize interference by avoiding areas with tall and dense buildings that may affect the signals between remote controller and aircraft. The performance of the aircraft is limited when flying at high altitudes. The maximum flight height of the aircraft is 500 m.

Beginner pilots should not be able to fly very far, and please always fly in open areas and keep your drone within line of sight. Mastering flight skills can result in better control, increased confidence, and an overall safer flight in any location.

Pre-flight Checklist

1. Make sure that the propellers are mounted properly. Check whether the propellers are broken or bent, and whether all the propellers are unfolded.

2. Remove the gimbal protector before powering on the drone and make sure that the battery is mounted in place (a click can be heard).

3. After the device is powered on and connected, check whether there are any warnings shown in the app. If yes, follow on-screen instructions and fly the drone after no warnings are detected.
* The vision systems cannot work properly in any of the following situations:

a) Flying over extremely dark surfaces, water or transparent surfaces, monochrome surfaces, or surfaces without clear patterns or texture;

b) Flying over obstacles with small surface areas (e.g., tree branches).

To know more about the compatibility of DJI Mini 2 SE, DJI Mini 4K, DJI Mini 2 and DJI Mini SE, please refer to the following table:

Popular Accessories

DJI Mini 2 360° Propeller Guard:
Specially designed with light texture, the propeller guard protects the
propellers from collisions, and improves flight safety. It is
especially applicable in indoor scenes with many obstacles, bringing
more safety guarantees for beginners.

DJI Mini 2 Intelligent Flight Battery:
One Intelligent Flight Battery provides a 31-min max flight time,
allowing you to explore more of your surroundings and fly with greater
peace of mind.

DJI Mini 2 360° Propeller Guard: Specially designed with light texture, the propeller guard protects the propellers from collisions, and improves flight safety. It is especially applicable in indoor scenes with many obstacles, bringing more safety guarantees for beginners.

DJI Mini 2 Intelligent Flight Battery: One Intelligent Flight Battery provides a 31-min max flight time, allowing you to explore more of your surroundings and fly with greater peace of mind.